proc_close

(PHP 4 >= 4.3.0, PHP 5, PHP 7, PHP 8)

proc_closeClose a process opened by proc_open() and return the exit code of that process

Descrizione

proc_close(resource $process): int

proc_close() is similar to pclose() except that it only works on processes opened by proc_open(). proc_close() waits for the process to terminate, and returns its exit code. Open pipes to that process are closed when this function is called, in order to avoid a deadlock - the child process may not be able to exit while the pipes are open.

Elenco dei parametri

process

The proc_open() resource that will be closed.

Valori restituiti

Returns the termination status of the process that was run. In case of an error then -1 is returned.

Nota:

If PHP has been compiled with --enable-sigchild, the return value of this function is undefined.

add a note

User Contributed Notes 5 notes

up
13
oohay251 at yahoo dot com
19 years ago
From various Internet posts and recent experience, I have observed that you cannot rely on proc_close returning the accurate return code of the child process. The return code also depends on wether or not you read from the stdout/stderr pipes, as my example shows. I work around this by writing the exit code to an additional file descriptor.

<?
$descriptorspec = array(
0 => array('pipe', 'r'), // stdin is a pipe that the child will read from
1 => array('pipe', 'w'), // stdout is a pipe that the child will write to
2 => array('pipe', 'w'), // stderr is a pipe that the child will write to
);
$proc = @proc_open("/bin/ls -l /etc/passwd", $descriptorspec, $pipes);
fclose($pipes[0]);
$output = array();
while (!feof($pipes[1])) array_push($output, rtrim(fgets($pipes[1],1024),"\n"));
fclose($pipes[1]);
while (!feof($pipes[2])) array_push($output, rtrim(fgets($pipes[2],1024),"\n"));
fclose($pipes[2]);
$exit=proc_close($proc);
print_r($output);
echo "exitcode $exit\n\n";

$descriptorspec = array(
0 => array('pipe', 'r'), // stdin is a pipe that the child will read from
1 => array('pipe', 'w'), // stdout is a pipe that the child will write to
2 => array('pipe', 'w'), // stderr is a pipe that the child will write to
);
$proc = @proc_open("/bin/ls -l /etc/passwd", $descriptorspec, $pipes);
fclose($pipes[0]);
fclose($pipes[1]);
fclose($pipes[2]);
$exit=proc_close($proc);
echo "exitcode $exit\n\n";

$descriptorspec = array(
0 => array('pipe', 'r'), // stdin is a pipe that the child will read from
1 => array('pipe', 'w'), // stdout is a pipe that the child will write to
2 => array('pipe', 'w'), // stderr is a pipe that the child will write to
3 => array('pipe', 'w'), // stderr is a pipe that the child will write to
);
$proc = @proc_open("/bin/ls -l /etc/passwd;echo $? >&3", $descriptorspec, $pipes);
fclose($pipes[0]);
$output = array();
//comment next line to get correct exicode
while (!feof($pipes[1])) array_push($output, rtrim(fgets($pipes[1],1024),"\n"));
fclose($pipes[1]);
while (!feof($pipes[2])) array_push($output, rtrim(fgets($pipes[2],1024),"\n"));
fclose($pipes[2]);
if (!feof($pipes[3])) $output['exitcode']=rtrim(fgets($pipes[3],5),"\n");
fclose($pipes[3]);
proc_close($proc);
print_r($output);
?>

Outputs on my system:

Array
(
[0] => -rw-r--r-- 1 root root 1460 2005-09-02 09:52 /etc/passwd
[1] =>
[2] =>
)
exitcode -1

exitcode 1

Array
(
[0] => -rw-r--r-- 1 root root 1460 2005-09-02 09:52 /etc/passwd
[1] =>
[2] =>
[exitcode] => 0
)
up
9
Uwe Ohse
9 years ago
Regarding: "Returns the termination status of the process that was run. In case of an error then -1 is returned."

This is, at best, misleading. It returns:
* -1 on error,
* WEXITSTATUS(status) if WIFEXITED(status) is true, or
* status if WIFEXITED(status) is false,
where status is the status parameter of waitpid().

This makes it impossible to differentiate between a relatively normal exit or a termination by signal, and reduces the value of the proc_close return code to a binary one (ok / something broke).

This can be seen in proc_open_rsrc_dtor() in ext/standard/proc_open.c (PHP 5.4.44, 5.6.12).
up
1
ashnazg at php dot net
17 years ago
It seems that if you configured --enable-sigchild when you compiled PHP (which from my reading is required for you to use Oracle stuff), then return codes from proc_close() cannot be trusted.

Using proc_open's Example 1998's code on versions I have of PHP4 (4.4.7) and PHP5 (5.2.4), the return code is always "-1". This is also the only return code I can cause by running other shell commands whether they succeed or fail.

I don't see this caveat mentioned anywhere except on this old bug report -- http://bugs.php.net/bug.php?id=29123
up
1
sergey1369 at narod dot ru
21 years ago
Under PHP/4.3.3RC2, in case of two processes
these function may hangs. Work around is not use
proc_close, or put it after all fcloses done.

For example, this code hangs.

$ph1 = proc_open("cat",
array(0=>array("pipe","r"),1=>array("pipe","w")),
$pipes1);
$ph2 = proc_open("cat",
array(0=>array("pipe","r"),1=>array("pipe","w")),
$pipes2);

fclose($pipes1[0]); fclose($pipes1[1]); proc_close($ph1);
fclose($pipes2[0]); fclose($pipes2[1]); proc_close($ph2);

This code worked for me:

$ph1 = proc_open("cat",
array(0=>array("pipe","r"),1=>array("pipe","w")),
$pipes1);
$ph2 = proc_open("cat",
array(0=>array("pipe","r"),1=>array("pipe","w")),
$pipes2);

fclose($pipes1[0]); fclose($pipes1[1]);
fclose($pipes2[0]); fclose($pipes2[1]);
proc_close($ph1); proc_close($ph2);
up
0
morrisdavidd at gmail dot com
16 years ago
Consider the following pseudo code:

$SOME_PROCESS = proc_open(/* something here */);
...
$status = proc_get_status($SOME_PROCESS);
...
$exitCode = proc_close($SOME_PROCESS);

If the external program has exited on its own before the call to proc_get_status, then $exitCode == -1

So consider using:
$actualExitCode = ($status["running"] ? $exitCode : $status["exitcode"] );
To Top